ASTM D3654 PDF

0 Comments

ASTM D – Designation: D /D M – 06 Standard Test Methods for Shear Adhesion of. ASTM D/DM: Standard Test Methods for Shear Adhesion of Pressure- Sensitive Tapes. A summary of ASTM standards relating to pressure sensitive tape is attached. The shear test procedures are also harmonized: ASTM D and PSTC.

Author: Tojar Zuzil
Country: New Zealand
Language: English (Spanish)
Genre: Music
Published (Last): 5 April 2015
Pages: 158
PDF File Size: 17.24 Mb
ePub File Size: 10.9 Mb
ISBN: 226-2-44464-153-5
Downloads: 7190
Price: Free* [*Free Regsitration Required]
Uploader: Fenrikus

Identification number of the company: This standard is subject to revision at any time by the responsible technical committee and must be reviewed asym Proceed to Checkout Continue Shopping.

Where width or other factors causing high adherence to backing make it impossible to remove the specimen at the prescribed rate, remove it at a rate as close to mm [30 in.

The components of the variance for the following factors were estimated: By navigating on this website, you accept their use.

Repeat for a total of three washes with this solvent. You can download and open this file to your own computer but DRM prevents opening this file on another computer, including a networked server.

ASTM D3654/D3654M – 06(2011)

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. The razor shall be held in position using side plates. The edges for about mm [5 in. For procedures B, C, D, and G remove? The roller shall move either mechanically or by hand at the rate of 10 6 0.

  EUGENE IONESCO THE BALD SOPRANO PDF

Width of specimen for Procedures E, F, and G if other than 12 mm [0. Transport of foodstuffs or medical; warmth or cold Available in compartment simple, double or icebox typify Isothermal boxes icebox for xstm wheels, scooters, motorcycles typify The radius of the curvature of the? In order to offer you the best service, Algomtl uses cookies.

ASTM D | Rycobel

Use of the Weibull distribution is an acceptable alternative. Already Subscribed to this document.

Test specimens should be taken from several rolls of a tape and, whenever possible, among several production runs of a tape. Record the time elapse in which the tape specimen has completely separated from the test panel.

Owen Zhang86 Procedures B, C, and D ast, be used to determine f3654 shear adhesion of the tapes generally used to close fiberboard boxes in packaging applications.

Standards Subscriptions from ANSI provides a money-saving, multi-user solution for accessing standards. The panel is mounted horizontally, tape side up, with the free end of the tape allowed to hang vertically over the round end of the panel.

Under no circumstances Algomtl can be held responsible for the content of the ads published. These censored data may have a time to termination rather than a time to failure. Allow the remaining mm [8 in. We have no amendments or corrections for this standard. Subscription pricing is determined by: Combining values from the two systems will result in non-conformance with the standard. Record the time elaspe in which the tape specimen x3654 separated completely from the test panel see Fig.

  ATEX ZONERING PDF

We invite you to read our terms of use. The 24 mm d36654 in.

ASTM D Standard: Shear Adhesion Tester for Pressure Sensitive Tapes

Strong conclusions about a speci? The values stated in each system are not be exact equivalents; therefore, each system shall be used independently of the other. The test plate with adhesive specimen is vertically hanged on the stand and its bottom is attached with a standard weight. You may delete a document from your Alert Profile at any time.

ASTM D3654

NOTE 4—Discard panels showing stains, discoloration, or many scratches. Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters. Conduct an analysis of the logarithm of the data to determine the desired descriptive or comparative statistics.