KP1010 DATASHEET PDF
KP Datasheet, KP PDF, KP Data sheet, KP manual, KP pdf, KP, datenblatt, Electronics KP, alldatasheet, free, datasheet. Above specification may be changed without notice. EVERLIGHT will reserve authority on material change for above specification. 2. KP KP Components datasheet pdf data sheet FREE from Datasheet4U .com Datasheet (data sheet) search for integrated circuits (ic), semiconductors.
|Published (Last):||21 August 2010|
|PDF File Size:||15.33 Mb|
|ePub File Size:||16.53 Mb|
|Price:||Free* [*Free Regsitration Required]|
As the KP is a high precision IC for cost critical solutions. High accuracy and high sensitivity enable the dedication in automotive applications as well as consumer products. For the triac pins 4 and 6with no voltage applied to the LED pins 1, 2check with an ohmmeter the resistance between pins 4 and 6, datashert should be high open circuit or at least greater than 1 megohm both ways, and this resistance should go down lower than ohms when voltage is applied to the LED, and should remain low even if the voltage is no longer present on the LED.
cosmo KP datasheet & applicatoin notes – Datasheet Archive
Absolute Pressure Sensor IC. These information are very good indeed. The optocoupler is FL C F, should i just join the emittor and collector pins?
Any help would be apreciated. First of all thanks for sharing such an useful information.
Mihai on September 17, at There is no law governing all things. Mihai on November 20, at 1: I like the way you explain things. Mihai on July 15, at 8: I was referring to the junction resistance.
When Firefox stops working, you fire up Chrome. The firehose by day and forty beers by night, An engineer may never sleep and still be just as bright.
It is surface micromachined with a monolithic integrated signal conditioning circuit realized in the state-of-the-art 0. Good design is as little design as possible. If you get a value either way or no value at all, then certainly there is a problem with the LED, and you should find another optocoupler. Arvind Vijaykumar on June 1, at I only have a digital multi meter. The question is which one is the right testing method?
I guess, it should work mostly the same as a normal triac. If the LED is good then we should check the phototransistor, you could measure it with the ohmmeter just like the LED between datasbeet 3 and 4 the emitter and collectordatasheett you should get a high resistance value both ways if the phototransistor is good. The nice thing about standards is that you have so many to choose from.
Some features may not work properly. High accuracy and high sensitivity enable the. Muhammad Akhlaq on May 30, at 9: Geert Van Droogenbroeck on November 18, at So kpp1010 current flows through the LED, the triac is triggered and it conducts both ways until the main current drops below a certain level.
Hi, Both methods are correct. Blumen on October 26, at 7: Sunil on March 3, at 3: Mihai on March 6, at 2: How the optocoupler Type SFH acts when the positive line is open.
Viliam on September 7, at 1: The alcohol never solved anything, but neither did water or milk. For response time or frequency response data, check the datasheet. In the automotive field the manifold air pressure MAP and barometric air pressure BAP are important parameters to compute the air-fuel ratio provided to the engine and for controlling spark advance to optimize engine efficiency.
KP110 Datasheet PDF
You helped me understand how to use a tester on a optocoupler Thanks. Thank you for the information. Sanu sebastian on Xatasheet 19, at It depends on the 2nd circuit you are supplying the voltage on collector of the optocoupler, optocoupler will never transfer the voltages of circuit1 to circuit2, it decreases resistance between your supplied voltages at collector and emitter on the input of circuit2.
Programmable Temperature Compensation and Calibration. Low Cost Bare Die Version. I have two circuits. Here I want to show you how to check if an optocoupler is working. In the automotive field the manifold air pressure MAP and barometric air pressure.
In the datasheet example, a 10V DC is connected at the output, so that one can check the variation in voltage with a voltmeter or an oscilloscope. The purpose of an optocoupler is to transfer signals from one circuit to another yet keep them galvanically isolated.
Mihai on February 6, at Step 2 If the LED is good then we should check the phototransistor, you could measure it with the ohmmeter just like the LED between pins 3 and 4 the emitter and collectorand you should get a high resistance value both ways if the phototransistor is good. Mihai on July 19, at 3: Hi, First of all thanks for sharing such an useful information. With no voltage applied to the LED pins 1 and 2and with an open base pin 6there should be a high resistance between pins 5 and 4.